Ashing furnaces SNOL 8.2/1100, up to 1100 °C, Omron E5CC-T controller
Ashing furnaces with muffle chamber made of ceramic fibres and exhaust chimney. Suitable for applications in industry, science and medicine.Side, top or down-opening door depending on modelOuter casing made of powder-coated sheet metalExhaust chimney with fanControl panel in the lower part of the ovenIncl. door safety switchFast heating timeGood stability and temperature distributionLow power consumptionWith temperature controller Omron E5CC-T: programmable PID controller with 8 programmes and 32 programming segments
Ashing/Burn off furnaces LV 3/11 - LVT 15/11
The models LV 3/11 - LVT 15/11 are especially designed for ashing in the laboratory. A special air intake and exhaust system allows air exchange of more than 6 times per minute. Incoming air is preheated to ensure a good temperature uniformity.Tmax 1100°CHeating from two sidesCeramic heating plates with integral heating element which is safeguarded against fumes and splashing, and easy to replaceInsulation only made of materials that are classified as not carcinogenic acc. to TRGS 905, class 1 or 2Housing made of sheets of textured stainless steelDual shell housing for low external temperatures and stabilityOptional flap door (LV) which can be used as work platform or lift door (LVT) with hot surface facing away from the operatorSolid state relays provide for low noise operationAir exchange of more than 6 times per minuteGood temperature uniformity due to preheating of incoming air220-240 V 1/N/PE 50/60 Hz connector as standardOption:Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and loadObservation hole in the oven doorProcess control and documentation via VCD software package for monitoring, documentation and controlHeight incl. exhaust tube (diam. 80 mm)External dimensions vary for versions with additional equipment. Dimensions on request.
ATEX Chemical membrane pump VP5 EX
The VP5 EX vacuum pump, together with the VDL series vacuum drying ovens, is ideally suited for the safe drying of flammable solvents.Resistant to a wide range of chemicalsVery quiet and low-vibration operationDesigned for S1 operating mode (continuous operation)Suction and pressure-side separators for collecting condensateEmission condenser at the pump outlet for solvent recondensationPower connection via fixed connection, pump supplied with blank cable ends without plugATEX-compliant
Auminum holder Nalgene™ KryoCane™, Type 5015
For frozen storage of cryovials 1.2, 1.5 or 2.0ml.
Bag mounting strips
Magnetic bag mounting strips made of stainless steel. For attaching vessels to the magnetic platform.
Base frames for CO2 incubators CB series
The base frame equipped with casters is used for the secure positioning and leveling of CO2 incubators.
Base tray for spring clamps
The base tray can be equipped with spring clamps of different sizes and used for tempering Erlenmeyer flasks in shaking water baths.Please order spring clamps for fastening Erlenmeyer flasks separately.
Base tray for test tube racks
The base tray can be equipped with a max. of 4 test tube racks and used for tempering test tubes in shaking water baths.Please order test tube racks separately.
Basic digital water baths JB Academy
An ideal choice for schools and colleges requiring a basic simple-to-use quality water bath. Base tray included as standard. A great value range consisting of three models.Ambient + 5 °C to 95 °CUnique Set and Forget™ technology, fast heat-up, reliable temperature controlStability ± 0.5 °CSimple, intuitive controls, quick and easy to set temperaturePractical front panel lock, disables front panel controls preventing unintentional temperature changes3 year warrantyAccessory polypropylene spheres or a lid must be used at temperatures between +60 °C and +99 °C. Please order lid and PP spheres separately.
Bath fluid Algicide Aquastab
Protective agent for the prevention and control of algae formation in bath thermostatsRecommended dosage: 5 mL / 10 litres of water2 % poly(dimethylimino)-2-hydroxy-1,3-propanediyl chlorideUse biocidal products with care. Always read the label and product information before use.
Bath fluid Polyclear Mix 30 Plus
Prevents premature rusting and the growth of algae. Ideal for use in circulators, water baths, shaking water baths or heating baths. For routine applications from 5 to 90 °C.
Bath liquids for thermostatic baths
Bath liquids.Use of the appropriate liquids for heat transfer listed here offers many advantages:Safe to use, non toxic, and generally odourless formulationsResistance to ageing and viscosity changes with low susceptibility to corrosion.Silicone oils (SIL).Non-flammable, with long operational life.Synthetic heat transfer fluids (Synth).Usually formulated from a hydrocarbon base with low viscosity within the recommended working temperature range.Viscosity.For optimal temperature stability the bath fluid must be of low viscosity.Fire point.Fluids can spontaneously ignite above a certain temperature. EN 61010 stipulates that the maximum working temperature of the liquid should be 25 °C below its' fire point.Heating up range.Prolonged use is not permitted as the self-heating effect within these liquids may cause the overtemperature protection system of the pump unit to operate and shut down the pump.Operating temperature range.Thermostats may only be operated for an extended time in this range under certain conditions. Viscosity must not exceed 30 mPas. Otherwise pumps will not achieve their stated performance figures.Working temperature range.The long-term use range for peak thermostatic bath performance. Maximum viscosity level is approx. 5 mPas.
Bath tanks for Temperature control systems IC/ICC, plastic
Plastic tanks up to 100 °C, only for water.
Bath tanks for Temperature control systems IC/ICC, stainless steel
Stainless steel tanks up to 200 °C, with bath drain.
Beakers, glass, jacketed wiht PTFE-Olive, type T-GL
DURAN®. For heating and cooling liquids. Thermostatting liquid is circulating between the double walls of the beaker jacket. With glass-screw connections GL14 with PTFE olives (O.D. 9mm, T-GL2000 with GL18 and O.D. 11mm) for thermostat hoses. Coolant ram pressure: 0.5bar at maximum, operating temperature: +120°C at maximum. Special sizes available on request.
Beakers, glass, jacketed, type T
DURAN®. For heating and cooling liquids. Thermostatting liquid is circulating between the double walls of the beaker jacket. With glass olives (O.D. 12mm) for thermostat hoses. Coolant ram pressure: 0.5bar at maximum, operating temperature: +300°C at maximum. Special sizes available on request.
Beer Force-Ageing-Test Bath BFT®5
We offer special air cooled circulator for the Beer Force-Ageing-Test. It is equipped with a programmer for the change between 0 °C / 40 °C and 0 °C / 60 °C in a 24 hour cycle. Casings and bath parts are made of stainless steel.
Benchtop Shaking Incubator 222DS
The Benchtop Shaking Incubator is a combination of a shaker and a temperature chamber, designed for shaking and heat treatment of sensitive samples. It replaces two devices, reduces time and space needed. It is very suitable for biochemistry, microbiology and medicine laboratories in which thermal and shaking treatment of samples is a daily used routine.High temperature working rangeCan be used in cold rooms tooDigital readout of all parameters - read temporary or preset RPM, temperature, time, accelerationParameter changes while the device is running (except timer)Last parameter values reside in the memory even if the device was switched offPrecisely adjusted and maintained temperature regulation within 0.5 °C of absolute deviation from the set temperatureHOLD and STEP time function with 1 minute resolutionEasy interchangeable platformsLid sensorUniveral attachement and non-slip mat please order separately.
Benchtop shaking incubator Enviro-Genie®
The Enviro-Genie® is an incubator, rotator, rocker and stirrer in one compact unit. It is ideal for the study of microorganisms and tissue cell growth under strictly controlled conditions of temperature and agitation. Peltier technology ensures high degree of accuracy, uniformity and stability.Crystal-clear backlit LCD displays all parameters at a glanceMagnetic stainless steel platform may be easily set to rock or rotate almost any containerTwo low and high speed magnetic stirrers incorporated, with revers stirringA variety of accessories are available to provide maximum application versatilityChamber air is gently and continuously re-circulated ensuring temperature consistency and uniformityShatterproof window allows for inspection of samples without disturbing chamber environmentOptional available: Horizontal orbital attachment for Western Blots and maintaining cells or solutions in suspensionWith visible and audible alarm for temperature and timeWith RS232 port for data acquisition and remote operationSpeed (rotation): 1 ... 35 rpmSpeed (rocking): 2 ... 70 cylcles per minScope of supply: Incubator, 1 x magnetic platform, 1 x clip plate each for 10 to 13 mm, 15 to 17 mm, 28 to 30 mm tubes, 4 x bag mounting strips, 1 x non-skid tray, 1 x wire rack