LLG Catalogue
Beard Mask, White, PP, Detectable
This beard mask has a detectable strip on the inside. That's why it can be detected by a dector machine at any time- even if the beard mask gets into the production.air-permeable and breathableideal for special hygienc-sensitive areas
Beard masks
non-woven fabricnon-irritating elastic bandsfood-safe23 x 46 cm100 pieces per package1,000 pieces per shipping unit
Bechtop centrifuge LMC-56
Universal centrifuge for operation with tubes, blood collection systems, gel cards, microtest and ELISA plates. Easy to operate, safe and easy to maintain with a large selection of accessories for the various applications.User-friendly centrifugation parameter input and simultaneous display of the set and actual parameter valuesSafe operation due to metal protective housing and metal lid, automatic imbalance switch-off and lid lockImproved chamber to reduce sample heating during centrifugationDifferent modes of acceleration and deceleration, including deceleration mode with switched off forced brakingDisplay of speed in revolutions per minute or in relative centrifugal forceTimer from 1 to 90 min or continuousPlease order rotors separately.
Beer Force-Ageing-Test Bath BFT®5
We offer special air cooled circulator for the Beer Force-Ageing-Test. It is equipped with a programmer for the change between 0 °C / 40 °C and 0 °C / 60 °C in a 24 hour cycle. Casings and bath parts are made of stainless steel.
behr COD Heating Blocks
COD acc. to ISO Precision heating blocks with 6, 12 or 24 sample positions. Flat surface heater for even temperature distribution to each sample position. Stainless steel and powder coated steel casing. Extensive insulation provides for inoffensive temperatures of the casing surfaces.End-to-end grooves in the precision aluminum plate at the bottom of the bores simplify sample handling and provide for exemplary safety of the analyst:During sample insertion the grooves cause pressure compensation. Thus even the most accurately fitting reaction vessels slip easily into the bores, which is required to effortlessly handle the behr insert and yoke type frames for RG 2 reaction vessels.When inserting the samples into the hot heating block adherent moisture on the vessel surface evaporates in sudden bursts. The grooves drain off the vapor which otherwise might cause the vessels to jump up and down which might eventually lead to the destruction of the vessels.In case of one or more vessels overflowing the liquid COD samples discharge through the grooves minimizing the danger of damages inside the block caused by acids.
behrosog 3 Scrubber
Infinitely variable throughputTransparent protective shield for safe operation of the unitExterior manual control elements with easy access prevent the analyst from touching hot glass partsAcid resistant diaphragm pump
behrotest ® column elution unit for the elution of soil samples
Column elution unit:Column elution unit in acc. with the LUA recommendation with 4-channel hose pump with controllable speed. The unit consists of :Assembly stand for the systemControllable 4-channel hose pump with fixed speedStorage vessel, 20 l4 elution columns, internal diameter 6 cm, 32 cm long, with 2 screwed joints (GL 45, with PTFE inserts) for simple filling of the columns4 collection bottles for the column eluate, 2 l, with screwed joint (GL 45) and deaerationSupply tube made of TYGON and PVC, with non-return valve in the supply to the columnPTFE tubes between columns and collection vesselsFlow rate 0.003 to 35 ml/minRange of speed 2 to 100 min-1Simultaneous control of all 4 channelsbehrotest® silica sand:for column elution unit, grain size 1 to 2 mm in acc. with DIN V 19736, 1000 g bottlebehrotest® silica wool:for column elution unit, 100 g bag
behrotest ® HTI 1 manual titration station
The HTI 1 manual titration station consists ofa burette with digital display anda magnetic stirrer with a precisely fitting holder for COD reaction vessels. A screen serves as a neutral background and allows the user to determine the colour change at the end of the titration precisely. Therefore a titration could always carried out under similar visual conditions. This improves the precision and the reproducibility of the results.The precise positioning of the reaction vessels in the holder on the top of the magnetic stirrer also contributes to this. The angled wing of the screen protects against lateral dazzling light.SpecificationsVoltage230 VAC/ 115 VACFrequency50/60 HzWeightapprox. 3.5 kgDimensions in mm (W x D x H)approx. 330 x 200 x 600
behrotest® CF 2+2 and CF 6, Semi-automatic Crude Fibre Extraction
They are ideally suited for:total crude fibre determination (part of the Weender animal feed analysis as performed in Europe)neutral detergent fibre and acid detergent fibre determination (NDF and ADF according to Van Soest)acid detergent lignin determination (ADL according to Van Soest)different fractions of fibre (cellulose, hemicellulose and pectin) behrotest® semi-automatic crude fibre extraction units simplify everday life in the lab:Easy operationThe analyst is guided through the procedure by messages on the display.behr ABP ("acknowledge before proceeding") method for optimum analytical safety. Possible manual operation of air and suction pumps.
behrotest® compact equipment for elution of solid matters
Percolation equipment to jointly examine the elution behaviour of inorganic and organic substances in solid matters. Including hose pump with 2 channels and 2 different pump tubes for a flow rate of 0.25-12 ml/min. and 0.66-33 ml/min. (Other pump tubes upon request).Complete equipment, consisting ofPercolation columns with pre-filters on sturdy standsStorage bottle with cap and tubeTubeEluate lead made of PTFEStorage vessel made of glass, cap with ventilation tube
behrotest® flow-through unit, Aquabox
The Aquabox flow-through unit enables the correct, expert determination of on-site parameters during the collection of soil and sewage samples. The unit permits the simultaneous determination of electrolytic and physico-chemical parameters under optimal and reproducible flow conditions.Aquabox is constructed of transparent, shock-resistant PETG, a thermoplastic copolyester. The transparent construction allows constant visual identification of problems during operation, e.g. sand or sediment contamination. All components which come into contact with water are made of non-wetting PETG (flow chamber and lid) or PP (inlet and outlet tubing). Therefore the water being sampled is not affected by any release of contaminants from the materials used for construction of the Aquabox. The lid is splashproof and easy to open and close by means of a quick-release fastener. The lid has 6 variable diameter, splashproof sensor holders for inserting sensors up to 25mm diameter (larger diameters available on request).The water spirals upward in the chamber around the positioned electrodes and flows out over the splashproof outer housing.Six holders in the lid with variable diameters provide secure sensor mounting in the peak flow area.On-site measurements are made easy due to the rugged construction materials.Water flow can be adjusted using a valve.An inlet bypass valve allows sampling.Aquabox is quick and easy to disassemble without the need for tools through a central threaded joint.Aquabox application areas:In the laboratory and on-site.In-line and point sample operation also possible.
behrotest® Multi-sample Extractors for Twisselmann Extraction
Economical and user-friendly units for extraction in accordance with Twisselmann:each sample position is individually adjustablecooling water distributor ensures an even cooling at all sample positionspractical stand for holding the condensers securely between the extractionsmounts for holding the spacers after the removal of the sample containers
behrotest® waste water mixers
behrotest ® homogenisers. With transportable sample vessels. Homogenisers for pre-treatment, splitting and homogenization of heterogeneous water samples in accordance with the quality assurance and quality control standards for wastewater examinations. The vessels of the homogenizers are protected against damage in the yolk type frame and can be carried easily by the two handles. They can be filled at the sampling location by a flattened inlet connection. Capacities from 2 to 25 l permit extraction and collection of multiple samples. Exact measurement of the sample quantities due to graduation. Subsequently, the transport rack is just placed on the magnetic stirrer in the laboratory or in the sampling vehicle and the homogeniser is immediately ready for use. The speed of the magnetic stirrer can be adjusted by a controller. The user can thus comply with the specified cone height in all cases. Oxygen is thus prevented from entering the samples. Dosed extraction of the homogenised sample via PTFE spindle stopcock. 12V, with adapter for mains connection.
behrotest® water samplers
For sampling from the water surface.Adjustable clamping device and end rod made of stainless steel, with choice of sample container as indicated. For sampling in accordance with DIN 38409 to H14/AOX a 1 litre borosilicate beaker is required. With 3-part handle, which is continuously adjustable between 1 and 3,75m. Ideal for use at sites which are difficult to access.
Bell caps for narrow-mouth reagent bottles, series 310, UN-approved
Tamper-evident ring, red, cup-shaped PTFE liner.
Bell caps for narrow-mouth reagent bottles, with degassing membrane, series 310, UN-approved
Tamper-evident ring, red, cup-shaped, perforated PTFE liner.
Bell jars, DURAN®
With ground joint neck, for vacuum use. Ground joint height: 50 mm.
Bellows, PTFE
Strainless connection of ground joint equipment; for compensating vibrations from vacuum pumps; for length compensation of heated columns; angular misalignment.Made of PTFE, with sharp folds and sealing rings on the outside; maximum deflection: 120°.
Bench balances FCD
Thanks to rechargeable battery operation, compact, lightweight construction, it is suitable for the use in several locations (production, warehouse, dispatch department, etc.). A visual and audible signal helps with portioning, dispensing or grading.LCD displayInterfaces RS-232
Bench balances FCE
Entry-level bench scale suitable as a letter and parcel balance, as well as a checkweighing balance in production.Large LCD displayBattery operation possibleScope of supply: Bench balance, protective working cover
Bench balances FCF
Compact bench balance with multi-purpose functionality and a high level of accuracy for use in industry, gastronomy and kitchen.Large backlit LCD displayBattery operation possibleScope of supply: Bench balance, protective working cover
Bench balances FFN
All-round bench balance for the ever-increasing hygienic requirements in the food, pharmaceutical and chemical industries. Thanks to rechargeable battery operation, compact, lightweight construction, it is suitable for the use in several locations.Large backlit LCD displayRecessed grips on the underside for easy transportationProtection against dust and water splashes IP65 (only when using rechargeable battery pack)