Drum pumps B2 Vario, mains-powered, PVDF
Lightweight and powerful pump for transferring small amounts of aqueous liquids up to 300 mPas from cans and drums with infinitely variable speed controller.Motor 230 V, 200 W (IP 24)Seal less pump tubeSuitable accessory flow meter requiredPump with tubing connectionSuitable for Naphthalin, Natriumhypochlorit, Nitric acid, Perchloric acid.Scope of supply: Motor B2 Vario, pump tube, hose connectors
Drum pumps B2 Vario, mains-powered, stainless steel
Lightweight and powerful pump for transferring small amounts of aqueous liquids up to 300 mPas from cans and drums with infinitely variable speed controller.Motor 230 V, 200 W (IP 24)Seal less pump tubeSuitable accessory flow meter requiredPump with tubing connectionStainless steel version for low-viscosity lubricants.Scope of supply: Motor B2 Vario, pump tube, hose connectors
Drum pumps GLP 25
GLP 25 is your ideal helper for clean and safe liquid transfer from small containers and drums up to 220 litres. Various media such as acids and bases low concentrated, dies, emulsions, dispersions and low-viscosity liquids can be measured out without any problems. Wetted materials are PP, stainless steel and Viton®. The pump is therefore additionally media resistant against aggressive liquids. Driveshaft made from stainless steel. Delivery rates from 1 to 20 l/min adjustable. Pump Set supplied with: motor, pump unit, PP, ¾" dia. inlet tubing (length 500, 700 or 1000mm), PP discharge tubing, 250mm long and adapter for drum necks of 40 to 58mm.
Drum pumps, "solvents", explosion-proof version, mains-powered
For safe handling of environmentally hazardous and aggressive liquids as well as inflammable and explosive fluids.For easily flammable hydrocarbons such as ethanol, gasoline, butanol, isopropanol, kerosene, methanol and petroleum.Supplied with: 230V motor, 5m cable and plug, pump tube and tubing connection, earthing strap
Flow Indicator with ball, SAN
For liquid flow from 50 ml/min in horizontal position, and 140 ml/min in vertical position. Minimum air flow 3 l/min horizontal and 8 l/min vertical. Speed of rotation of ball proportional to flow. Not to be used with corrosive fluids or over +50 °C.
Flow Indicator with paddle wheel, SAN
For liquid flows down to 5 ml/sec. Wheel spins freely and speed of rotation is proportional to flow rate. Maximum recommended flow rate up to 95 ml/sec, max 2 bar pressure. Not to be used with corrosive fluids or over +85 °C. Can be used with gases.
Flow meter TR3
Can be combined with all drum and container pumps. For thin-bodied fluids.Measurement according to the turbine wheel principleFree-rotatable after assemblyVariable display alignmentLarge illuminated displaySimultaneous display of subset (4-digit) and total quantity (7-digit)Display of the partial and total volumeCustomary 1.5 V batteries (AAA)
Foot pumps OTAL®, battery-pumps
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeWith delivery tubes made of PP/PVCFor safe filling of car batteries with acid or distilled waterWith tube shutoff valveWith dosing tip for precise filling
Foot pumps OTAL®, PP
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PPUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor weak acids, alkalis and detergents
Foot pumps OTAL®, PP, with tube and stopcock
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PPUniversal bungs made of soft PVC, for container openings of 30 – 70 mm1.5 m discharge tube, PVCStopcock made of PP/PE (Ø 10 mm)
Foot pumps OTAL®, PVDF
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PVDFUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor acids, alkalis and chlorine bleaching, not for heavily oxidising acids and alkalis
Foot pumps OTAL®, stainless steel
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of stainless steelUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor liquids that are not easily flammable in Hazard Category AIII (VbF)
Gas-tight Barrel pump
With flexible discharge tubing for drawing off into larger canisters and containers. Convenient liquid transfer as the canister can be left standing on the floor. The connection cone is pressed against the canister manually.The pump is fitted with a gas-displacement device for odour-free, liquid transfer. The pump can be hermetically sealed with 2 ball valves.Parts in contact with media: Stainless steel AISI 304 (1.4301), PTFEWith gas-tight barrel screw joint, 2" fine threadNot suitable for acetone!
Gas-tight barrel pump, PP
The gas-tight barrel pump reduces the escape of dangerous, health-endangering or malodorous gases when filling liquids. The resulting vapours are returned directly to the original container via the gas pendulum line.Medium-contacting parts, PP, PE and PVC (hose)Steplessly extendable telescopic tube for barrel depths of 40 - 67 cmUniversal adapter for container openings of 34 - 70 mm
Hand pumps OTAL®, battery-pumps
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeWith delivery tubes made of PP/PVCFor safe filling of car batteries with acid or distilled waterWith tube shutoff valveWith dosing tip for precise filling
Hand pumps OTAL®, PP
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PPUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor weak acids, alkalis and detergents
Hand pumps OTAL®, PP
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PPFor small containers, up to 10 lUniversal bungs made of soft PVC, for container openings of 20 – 36 mmFor weak acids, alkalis and detergents
Hand pumps OTAL®, PP, with tube and stopcock
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PPUniversal bungs made of soft PVC, for container openings of 30 – 70 mm1.5 m discharge tube, PVCStopcock made of PP/PE
Hand pumps OTAL®, PVDF
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PVDFUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor acids, alkalis and chlorine bleaching, not for heavily oxidising acids and alkalis
Hand pumps OTAL®, stainless steel
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of stainless steelUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor liquids that are not easily flammable in Hazard Category AIII (VbF)
Hand lever pump, alu
Lever pump for petrochemical substances, made of stable aluminium cast, valves and pistons are made of plastic (PA).Suitable for barrel threads M 64x4 or R 2"With closure device (for padlock)Telescopic tube 470 ... 925 mmScope of supply: Lever pump, hose kit, hose length 1.5 m, electrically conductive, with outlet elbow and bend protection spring
Mini solvent pump
The self-closing discharge (with auto-stop function) of the Mini solvent pump ensures absolutely precise filling with no dripping at all. Dosing is even easy in very small containers such as test tubes, which present no problems. A hose can optionally be fastened onto the discharge spout (internal Ø 6 mm), thus making it possible to fill the container from a greater distance.The Mini solvent pump is especially compact and very well balanced, which makes it possible to fill without tipping, even from very small containers.Thanks to its sturdy design and high-quality materials, the Mini solvent pump consistently ensures neat and reliable filling throughout its long service life, easily and conveniently.Ideal for 1-5 l containersConnecting thread GL 45Parts in contact with medium made of PTFE and stainless steel (1.4301, 1.4404)PTFE hose (6 x 8 mm) 0.4 mIncluding grounding cable 2 mAdapters available as accessories for S 40, GL 38 and GL 32
Siphons, LDPE/PVC
Transparent with stopcock. Simple to use, suitable for occasional dispensing of non-aggressive liquids from a higher drum to a lower vessel, following the siphoning principle.
Solvent pump foot operated, with flexible tubing
For filling off high purity liquids such as solvents. Due to the barrel screw joint and the stopcock, the container and the pump can be hermetically sealed. Electrostatic charge can be dissipated through the accessory antistatic set (please order seperately).Medium-contacting parts made of stainless steel (1.4301) and PTFEFor barrels up to 220 litres, immersion tube can be steplessly adjusted to the barrel depthSuitable for steel barrels with R 2'' thread
Solvent pump foot operated, with rigid angled tube
For filling off high purity liquids such as solvents. Due to the barrel screw joint and the stopcock, the container and the pump can be hermetically sealed. Electrostatic charge can be dissipated through the accessory antistatic set (please order seperately).Medium-contacting parts made opf stainless steel (1.4301) and PTFEFor barrels up to 220 litres, immersion tube can be steplessly adjusted to the barrel depthSuitable for steel barrels with R 2'' thread
Solvent pump hand operated
For contamination-free removal of organic solvents and flavouring agents. Can be completely closed off with two ball valves so that no dangerous vapours can escape after dispensing. Electrostatic charge can be dissipated through the accessory antistatic set (please order separately).Medium-contacting parts are made of stainless steel (1.4301) and PTFEFor containers up to 60 litresSuitable for containers with R 2'' thread
Solvent pump hand operated, for tinplate canisters
For contamination-free removal of organic solvents and flavouring agents. Can be completely closed off with two ball valves so that no dangerous vapours can escape after dispensing. Electrostatic charge can be dissipated through the accessory antistatic set (please order separately).Medium-contacting parts are made of stainless steel (1.4301) and PTFEFor containers up to 60 litresIncl. connector thread for pull-out spouts with Ø 35 mm
Thread adapter set
Thread adapter set consisting of:3/4'' Hünersdorff3/4" Kautex3/4" cylindrical R 3/4" barrel thread3/4" conical R 3/4" barrel threadHex wrench for threaded adapter
Thread adapter, stainless steel V2A
For pumps, drain cocks or other connections.Seal made of ePTFEElectrically conductiveSuitable for flammable liquidsAutoclavableFood safe
Universal thread adapter, stainless steel
For drums and other containers with an opening of 48 – 75 mm diameter, regardless of the respective thread. The thread adapter can be mounted quickly and easily with clamping screws. With G2" connector thread for drum screw connections and pumps with immersion tube diameter up to 32 mm.