Glass microfibre filters, grade GF/B, sheets
Glass microfibre filters have a fast filtration and a high loading capacity and particle retention rate. Manufactured without chemical binder from high grade borosilicate glass. (Exception: GF6, GF9). They are suitable for gravity or low suction filtration. Filtration speeds generally very much higher than conventional cellulose papers. Efficient retention of micron size particles. Must be used flat. Ideal for use in flat perforated plate Buchner type funnels (not sintered glass models). Can be used up to 500 °C.Three times thicker and with greater wet strength than GF/A. Particle retention to 1µm.
Glass microfibre filters, grade GF/C / GF/C RTU, pre-treated
Grade GF/C is pre-rinsed and dried, grade GF/C RTU is additionally pre-treated with washing, drying, cooling (in a desiccator) and weighing steps, aligned to the requirements of EN 872. It is certified that these filters have weight loss of less than 0.017 mg/cm2 after preparation, which is required by the standard. Each grade GF/C RTU ready-to-use filter is placed in an individually barcoded aluminum pan that notes the filter weight. Each box contains an additional box ID and barcode that can be used to download the weights of all 100 pans in that box.Applications: For cell harvesting, liquid scintillation counting and binding assays, especially suitable for use in applications involving air filtration and for gravimetric analysis of volatile materials where ignition is involved.
Glass microfibre filters, grade GF/C, round filters
Glass microfibre filters have a fast filtration and a high loading capacity and particle retention rate. Manufactured without chemical binder from high grade borosilicate glass. (Exception: GF6, GF9). They are suitable for gravity or low suction filtration. Filtration speeds generally very much higher than conventional cellulose papers. Efficient retention of micron size particles. Must be used flat. Ideal for use in flat perforated plate Buchner type funnels (not sintered glass models). Can be used up to 500 °C.Extremely efficient filter made to retain fine particles and micro organisms. Particle retention to 1.2 µm.
Glass microfibre filters, grade GF/C, sheets
Glass microfibre filters have a fast filtration and a high loading capacity and particle retention rate. Manufactured without chemical binder from high grade borosilicate glass. (Exception: GF6, GF9). They are suitable for gravity or low suction filtration. Filtration speeds generally very much higher than conventional cellulose papers. Efficient retention of micron size particles. Must be used flat. Ideal for use in flat perforated plate Buchner type funnels (not sintered glass models). Can be used up to 500 °C.Extremely efficient filter made to retain fine particles and micro organisms. Particle retention to 1.2 µm.
Glass microfibre filters, grade GF/D
Glass microfibre filters have a fast filtration and a high loading capacity and particle retention rate. Manufactured without chemical binder from high grade borosilicate glass. (Exception: GF6, GF9). They are suitable for gravity or low suction filtration. Filtration speeds generally very much higher than conventional cellulose papers. Efficient retention of micron size particles. Must be used flat. Ideal for use in flat perforated plate Buchner type funnels (not sintered glass models). Can be used up to 500 °C.Thick filter made from less fibres and retaining around 3µm particles with a very high loading capacity. Extremely high speed. Particle retention to 2.7µm.
Glass microfibre filters, grade GF/F, round filters
Glass microfibre filters have a fast filtration and a high loading capacity and particle retention rate. Manufactured without chemical binder from high grade borosilicate glass. (Exception: GF6, GF9). They are suitable for gravity or low suction filtration. Filtration speeds generally very much higher than conventional cellulose papers. Efficient retention of micron size particles. Must be used flat. Ideal for use in flat perforated plate Buchner type funnels (not sintered glass models). Can be used up to 500 °C.This ultra-fine filter has a 98 % retention efficiency for particles as small as 0.7 µm in liquids. Particle retention to 0.7 µm.
Glass microfibre filters, grade GF/F, sheets
Glass microfibre filters have a fast filtration and a high loading capacity and particle retention rate. Manufactured without chemical binder from high grade borosilicate glass. (Exception: GF6, GF9). They are suitable for gravity or low suction filtration. Filtration speeds generally very much higher than conventional cellulose papers. Efficient retention of micron size particles. Must be used flat. Ideal for use in flat perforated plate Buchner type funnels (not sintered glass models). Can be used up to 500 °C.This ultra-fine filter has a 98 % retention efficiency for particles as small as 0.7 µm in liquids. Particle retention to 0.7 µm.
Glass microfibre filters, MG 160 / MGA / MGG
Suitable for analytical and gravimetric analyses, as well as a pre-filter.HydrophilicAir / Gas FiltrationLiquid FiltrationNon-sterile
Glass microfibre filters, MGB / MGC / MGD / MGF
Suitable for analytical and gravimetric analyses, as well as a pre-filter.HydrophilicLiquid FiltrationNon-sterile
Glass Stirrer Bearings, PTFE
Combination of a borosilicate glass piece with ground joint, an interior PTFE shaft guide with integrated special gasket and a GL screw cap made of PPS. The special gasket made of PTFE and an FPM o-ring which is compressed by a GL screw cap provide a good sealing of the stirrer shaft. This gasket can be exchanged after wearing. Suitable for vacuum, perfect bearing for stirrer shafts made of stainless steel, glass and for BOLA Stirrer Shafts.
Glass units for vacuum filtration, PTFE-coated
Type 163. For particle testing or radiochemical work. For ultrafiltration and sterile filtration. Autoclavable. PTFE-coated, steel screen filter support.
Glass vacuum filter holders, glass frit
Compact, glass vacuum filter holders for simple particle testing and clarification of solutions. With glass frit membrane filter support and anodised aluminium clamp.Scope of delivery:Size 25 mm, 30 ml: Glass vacuum filtration unit with filter support consisting of PTFE ring and glass fritSize 47/50 mm, 250 ml: Glass vacuum filtration unit with silicone cover and filter support consisting of PTFE ring and glass frit
Gooch crucibles, porcelain
Made from porcelain with perforated bottoms. They need filter paper for filtering process.
Graduated centrifuge tubes, conical, PMP
Autoclavable. Withstand temperatures up to 170 °C. High chemical resistance. Good transparency. Cannot be used with naked flame.
Graduated centrifuge tubes, conical, PP
Autoclavable. Withstand temperatures up to 120 °C. High chemical resistance. Good transparency. Cannot be used with naked flame.
Ground joint clamps, POM
For securing the link between socket and cone.Very good chemical resistanceMax. operating temperatur 150 °CColour coded sizes
Ground joint clips for sleeve connections, wire, Chrome-nickel steel
Chrome-nickel steel.
Ground Joint GL Adapters, PTFE
Black, PPS screw cap with GL45 thread or blue PP, screw cap with GLS80 thread, movable insert with ground joint made of PTFE. Transition from a ground joint to a glass thread. The body can be turned independently from the screw cap. The complete, assembled adapter can be removed and fixed onto another bottle without the risk of disarranging the tubing. Very good chemical resistance, for working temperatures up to max. +250 °C.
Ground Joint Reducing Sets
This set consists of PTFE reducing rings graduated in ground joint sizes 14.5 / 18.8 / 24 / 29.2 / 34.5 / 45 and 60. With these rings, different cone and socket sizes can be connected. For example, it is possible to fit a 14.5 cone into a socket of 45. Also other combinations are possible. With this set you can practically cover all requirements within the lab.
Ground joint stoppers, borosilicate glass 3.3, semi hollow
DIN 12252. With octagonal grip.
Ground joint stoppers, borosilicate glass 3.3, solid
DIN 12252. With octagonal grip.
Guko set, EPDM
Consisting of 8 conical rubber seals in sizes 22 to 84 mm, made of ethylene-propylene-diene rubber, for filtering flasks. Autoclavable.