Manifolds Microsart®, for Biosart® 100 monitors
For microbiological quality control. Quick connectors at both sides of the manifolds enable fast connections of either tubing, another manifold or end caps. Various funnel and filtration units are available.Full autoclavability without disassemblySterile ventingReduced risk of secondary contaminationLow working heightRubber feets providing better stability at the workplaceScope of supply: Manifold, filter base support with sinter frit, Biosart® adapter, blind coupling, 20 cm tubing and venting filter
Manifolds Microsart®, for Biosart® 250 funnels
For microbiological quality control. Quick connectors at both sides of the manifolds enable fast connections of either tubing, another manifold or end caps. Various funnel and filtration units are available.Full autoclavability without disassemblySterile ventingReduced risk of secondary contaminationLow working heightRubber feets providing better stability at the workplaceScope of supply: Manifold, filter base support with sintered frit for 47 and 50 mm membrane filters, blind coupling, 20 cm tubing and plug for venting holes
Manifolds Microsart®, including stainless steel funnels
For microbiological quality control. Quick connectors at both sides of the manifolds enable fast connections of either tubing, another manifold or end caps. Various funnel and filtration units are available.Full autoclavability without disassemblySterile ventingReduced risk of secondary contaminationLow working heightRubber feets providing better stability at the workplaceScope of supply: Manifold, filter base support with sintered frit for 47 and 50 mm membrane filters, blind coupling, 20 cm tubing and plug for venting holesDimensions without funnels and tubing
Membrane filter 19 mm, Nuclepore™, Track-Etched, PC
Track-etched for highly defined pore size and high pore densityTreated with PVP to render it hydrophilicLow extractables, minimizing sample contamination riskHigh chemical resistance and good thermal stability for a wide range of sample typesLow, consistent ash and low tare weightsSmooth flat surface for high particle visibility
Membrane filter dispenser Sentino™
The filter dispenser is ideal for microbiological test laboratories with a high throughput. The device is designed to hold 200 membrane filters. Individual membrane filters are dispensed aseptically at the touch of a button on the soft-touch keypad. Refill packs can be easily loaded and unloaded at any time. Guide plates help when loading refill packs to prevent jamming. The dispenser can be plugged into main power source or operated with the NiMH rechargeable battery for mobile use.Dimensions: 120 x 220 x 200 mmWeight: 0.9 kgScope of supply: Membrane filter dispenser, power transformer with EU/UK/US power cord, user guide
Membrane Filter Dispenser, Microsart® e.motion
With this dispenser you can choose between three operating modes. Operation by push button, sensor or foot switch. The dispenser is easy to transport thanks to its low weight and handy handle. The battery-operated model of the Microsart®e.motion dispenser can also be used wirelessly. This means you benefit from greater flexibility in work areas without a power connection.Capacity for up to 250 membrane filtersCleaning with standard disinfectants possibleEasy transportDimensions (WxDxH) 172 x 233 x 230 mm
Membrane filter holders, PC
Reusable filter holder, without filter. Filter has to be selected separately. For particle removal, sterile filtration of aqueous solutions or for venting of sterile vessels. Autoclavable. With Luer connection.
Membrane filter PES
Circular filter for ultrafiltration for sample concentration in stirring cells. The PES diaphragm offers a high flow rate.
Membrane filter PES, hydrophil
White. They are recommended for the filtration of aqueous solutions and proteins. Due to their low content of extractable substances, they are suitable for sample preparation in environmental analysis.High flow ratesLow non-specific protein adsorptionHigh resistance
Membrane Filter, hydrophobic, PTFE
Made entirely of PTFE (polytetrafluorethylene), reinforced by Polypropylene net.Permanently hydrophobicAllowing passage of air even at low differential pressureResistant to almost all chemicals, very strong acids, cryoliquids, alkalis, aggressive organic solventsMust be pre-wetted with an organic solvent, such as ethanol, methanol or isopropanol, before filtration of aqueous samplesMax. Temperature 145 °C
Membrane Filter, mixed cellulose ester
Recommended for clarification and sterilisation of aqueous solutions, microbiological analysis and particle counts.Qualified for aqueous solutions (pH 4-8), hydrocarbons and some dilute solventsHigh non-specific adsorption: 160 µg/cm2 for gamma globulin and pore size 0.2 µm (decreases with increasing pore size)High mechanical stability, ideal for gravimetrical measurementsMaximum temperature 180 °C
Membrane filters Cellulose acetate PORAFIL®CA
These membranes of cellulose acetate have a low protein binding capacity and are suited for aqueous and alcoholic media. The membranes are hydrophilic and can be used for hot gases up to 180 °C. They can be sterilised.
Membrane filters Durapore®, PVDF
White. For filtration of biological solutions.HydrophilVery low protein bindingAutoclavable
Membrane filters EZ-Pak, mixed cellulose ester
White. For general microbiological analysis.SterileIndividually-packedGriddedWith imprint of article numbers, batch numbers, pore sizes and sequential numbers4 x 150 membrane filters
Membrane Filters Microsart™ e.motion
The membrane filters suitable for use in the Microsart™ e.motion are individually sterile-sealed,without protective paper on top of each filter, in a specially designed individual package on a band. For complete traceability, the membrane filter type, diameter, lot number and a unique serial number are printed on the package of each membrane filter unit. All Microsart membrane filters are "multi-fit" and can be used in all standard dispenser systems.The membrane filters have a diameter of 47 mm or 50 mm, and are white, green or grey with a high-contrast 3.1 mm grid.
Membrane Filters Microsart™ e.motion, High Flow
The membrane filters suitable for use in the Microsart™ e.motion are individually sterile-sealed,without protective paper on top of each filter, in a specially designed individual package on a band. For complete traceability, the membrane filter type, diameter, lot number and a unique serial number are printed on the package of each membrane filter unit. Specially developed pore structures of the 0.45 ìm high Flow membrane filters permit faster filtration based on their high flow rates and throughputs.All Microsart membrane filters are "multi-fit" and can be used in all standard dispenser systems.The membrane filters have a diameter of 47 mm or 50 mm, and are white, green or grey with a high-contrast 3.1 mm grid.
Membrane filters Nitrocellulose PORAFIL®NC
PORAFIL® NC membranes are made from cellulose nitrate. They are easily wettable and suited for filtration of aqueous solutions. In dry atmosphere these membranes are thermally stable to 125 °C and can be autoclaved at 121 °C.
Membrane filters Polycarbonate PORAFIL®RC
Polycarbonate membranes are mainly used for the determination of AOX.
Membrane filters Polyester PORAFIL®PE
Polyester membranes are hydrophilic and particularly suited for fine filtration, dust analysis, aerosol analysis and ultra-purification of solvents.
Membrane filters Polytetrafluoroethylene PORAFIL®TE
Membranes of polytetrafluoroethylene (PTFE) are particularly suited for aggressive media, since they are chemically inert towards aqueous and organic solutions as well as towards concentrated acids and bases. These membranes are hydrophobic, thus the pressure for filtration of aqueous solutions has to be higher than the breakthrough pressure. PORAFIL® TE membranes can be used at temperatures up to 145 °C
Membrane filters PORAFIL®CM
Membranes of cellulose mixed esters are ideal for gravimetric analysis. They are particularly suited for aqueous solutions. The hydrophilic membrane is thermally stable to 125 °C and can be autoclaved at 121 °C. This membrane is often used for contamination tests.
Membrane filters PORAFIL®CM, with grid
Membranes of cellulose mixed esters are ideal for gravimetric analysis. They are particularly suited for aqueous solutions. The hydrophilic membrane is thermally stable to 125 °C and can be autoclaved at 121 °C. This membrane is often used for contamination tests.
Membrane filters PORAFIL®MV, white
These cellulose mixed ester membranes are reinforced with a polyester fabric. Their filtration properties are very similar to membranes PORAFIL® CM, however, they are mechanically much more stable.