Gauge THERMOVAC TTR 101
The THERMOVAC TTR 101 combines the Pirani filament with a small capacitive measuring device. This enables precise measurements in the rough vacuum range.Compact sizeWith display for easy reading of the measured pressureEasily replaceable sensor elementLED signal for set point relay statusShort cycle operationConnection flange KF DN 16Complies with NRTL, ETL, RoHs, and WEEE standards
Gauge THERMOVAC TTR 91 RN
The gauge is equipped with the latest filament pirani technology to enable robust pressure measurement. The integrated filter protects the gauge from particle contamination. The LED light rings not only display basic information, but also indicate the pressure range.Compact sizeEasy maintenance without toolsFilament made of tungstenAnalogue output 0 to 10 VConnection plug RJ45/FCC68Flange KF DN 16
Hand-operated vacuum pumps Nalgene™
With PVC casing. Vacuum of approx. 86 mbar can be achieved and maintained. With outlet valve with detachable cover and separate vacuum release lever. Tubing connection nozzle fits tubing with an internal diameter of 6.4 mm. Supplied with 60 cm length of clear plastic tubing.
Hand-operated vacuum pumps Nalgene™, with vacuum gauge
With PVC casing. Vacuum of approx. 86 mbar can be achieved and maintained. With outlet valve with detachable cover and separate vacuum release lever. Tubing connection nozzle fits tubing with an internal diameter of 6.4 mm. Supplied with 60 cm length of clear plastic tubing. Can be disassembled for repair or replacement of internal parts.
In-line valves
Butterfly design. Housing made of stainless steel with fluoroelastomer seal. Two Buna-N rings act as rotary shaft seals. Helium leak-tested. Leak rate 1 x 10-6 mbar x l/s. Excellent throughput.
Laboratory freeze dryer VaCo 10
Freeze dryer in modular design for routine applications in the laboratory. Cooling is done by air-cooled compressor with direct temperature measurement at the cooling surface. A pre-cooling of the condenser is possible to avoid a delayed start or thawing of the samples. Further functions are the display of the vacuum and temperature curves, an error message memory and an operating hours counter.3 program places with 3 drying stages eachOperation via 4,3" colour touch screenDisplayed actual values during operation: Condenser temperature, vacuum (mbar), timeStainless steel housing resistant against commercial disinfectantsCFC-free refrigerantOperating language: English or German, other languages on request.-Adjustable parameters for each drying stage: Hold-up time, vacuum setpoint, (shelf space temperature (with the option heated shelf spaces) -Automatic defrosting of the ice condenser-Variable shelf spaceThe perfectly matched single parts of the modular system can be combined individually. All required parts of the optional accessories must be ordered separately.SpecificationsIce condenserTemperature:-50 °C or -80 °CIce condensor capacity:15 kg / 24 hmax. ice capacity:20 kgVolume:50 lCooling system:one-stage (-50 °C) / two-stage (-80 °C)Material:Stainless steel 1.4404/AiSi316LDimensions (Ø x H ):400 x 400 mmBasic unitWeight:75 or 90 kg (depending on the version ice condenser)Dimensions (W x D x H):750 x 750 x 900 mmPower supply:230 V, 50/60 Hz (-50 °C) / 400 V, 50/60 Hz (-80 °C)
Laboratory freeze dryer VaCo 2
Freeze dryer in modular design for routine applications in the laboratory. Cooling is done by air-cooled compressor with direct temperature measurement at the cooling surface. A pre-cooling of the condenser is possible to avoid a delayed start or thawing of the samples. Further functions are the display of the vacuum and temperature curves, an error message memory and an operating hours counter.3 program places with 3 drying stages eachOperation via 4,3" colour touch screenDisplayed actual values during operation: Condenser temperature, vacuum (mbar), timeStainless steel housing resistant against commercial disinfectantsCFC-free refrigerantOperating language: English or German, other languages on request.The perfectly matched single parts of the modular system can be combined individually. All required parts of the optional accessories must be ordered separately.SpecificationsIce condenserTemperature:-50 °C or -80 °CIce condensor capacity:2 kg / 24 hmax. ice capacity:3 kgVolume:5.7 lCooling system:one-stage (-50 °C) / two-stage (-80 °C)Material:Stainless steel 1.4404/AiSi316LDimensions (Ø x H ):220 x 150 mmBasic unitWeight:45 or 58 kg (depending on the version ice condenser)Dimensions (W x D x H):490 x 470 x 440 mmPower supply:230 V, 50/60 Hz
Laboratory freeze dryer VaCo 5
Freeze dryer in modular design for routine applications in the laboratory. Cooling is done by air-cooled compressor with direct temperature measurement at the cooling surface. A pre-cooling of the condenser is possible to avoid a delayed start or thawing of the samples. Further functions are the display of the vacuum and temperature curves, an error message memory and an operating hours counter.3 program places with 3 drying stages eachOperation via 4,3" colour touch screenDisplayed actual values during operation: Condenser temperature, vacuum (mbar), timeStainless steel housing resistant against commercial disinfectantsCFC-free refrigerantOperating language: English or German, other languages on request.-Adjustable parameters for each drying stage: Hold-up time, vacuum setpoint, shelf space temperature (with the option heated shelf spaces)The perfectly matched single parts of the modular system can be combined individually. All required parts of the optional accessories must be ordered separately.SpecificationsIce condenserTemperature:-50 °C or -80 °CIce condensor capacity:5 kg / 24 hmax. ice capacity:8 kgVolume:16 lCooling system:one-stage (-50 °C) / two-stage (-80 °C)Material:Stainless steel 1.4404/AiSi316LDimensions (Ø x H ):270 x 280 mmBasic unitWeight:60 or 75 kg (depending on the version ice condenser)Dimensions (W x D x H):800 x 530 x 400 mmPower supply:230 V, 50/60 Hz
Laboratory software labworldsoft® 6 Lite
Laboratory software for monitoring, controlling and recording data of IKA devices. The Lite version is the entry-level model and is ideal for monitoring and controlling a single IKA device. With the help of a PC, process dependencies can be defined, routine tasks can be automated, measurement recordings can be defined and real-time calculations can be created.1 IKA device selectableSupports FDA 21 CFR Part 11 requirementsSupports advanced user management (user, super user, administrator)Supports labworldsoft® Server1 year of support with new versions of labworldsoft® 6 Lite
Laboratory Vacuum Pump Microsart® e.jet
The laboratory vacuum pump for the filtration of samples in microbiology. During the vacuum filtration, the filtrate is directly discharged to the drain.Transmembranous pressure of less than 700 mbar, acc. ISO 8199Constant flow ratesDefined maximum vacuumSuitable for gases and liquids
Laboratory vacuum pump Microsart® maxi.vac
The electric neoprene diaphragm pumps are suitable for routine use in a microbiological laboratory. Controlled vacuum ensures that stressed microorganisms (e.g., bacteria) are gently concentrated on the membrane filter surface. This leads to lower mortality, which in turn leads to higher recovery rates and shorter incubation times.Low noise levelOil and maintenance freeParallel filtration with multiple strips
Laboratory vacuum pump Microsart® mini.vac
The electric neoprene diaphragm pumps are suitable for routine use in a microbiological laboratory. Controlled vacuum ensures that stressed microorganisms (e.g., bacteria) are gently concentrated on the membrane filter surface. This leads to lower mortality, which in turn leads to higher recovery rates and shorter incubation times.Low noise levelOil and maintenance freeSingle filtration with single bar or single filter holder
LLG-Desiccant drying agents, silica gel, self-indicating
With orange indicator colour. Self-indicating drying agent free from any heavy metals and therefore environmentally compatible. The gel is naturally orange when active and at a 6 weight-% saturation level. As the gel adsorbs moisture, the colour changes into green.The range of application is identical with that of white silica gel. The colour change, however, represents a great advantage since it allows monitoring of the saturation level. The gel can be regenerated when heated at a temperature of maximum 120 °C until it turns to its original orange colour.The safety data sheets of these products are available under www.llg-labware.com.
LLG-Desiccators, soda-lime glass, with lid, stopcock and porcelain plate
Desiccator made of soda-lime glass with lid, porcelain plate and stopcock. The stopcock has an outer diameter of about 9 mm.
LLG-Plate for desiccator, porcelain
Perforated. Without feet. To DIN 12911. 20mm diameter central hole and 5mm diameter outer holes.
LLG-Vacuum desiccator cabinets, polycarbonate, square form, "Heavy Duty"
High-quality and stable construction made of polycarbonate. Highly transparent, lightweight, shatterproof and stackable. The Silicon O-ring and specially designed locking clip allow use without grease. Three-way stopcock provides great convenience for consistent vacuum draw, vacuum release or gas exchange e.g. inert gas. Stopcock outer diameter: 9.5 mm. Hose connection outer diam. 9.5 mm. Maximum vacuum of 1,3 mbar ( 1.33 x 10-4 MPa) for more than 72 hours, with built-in vacuum gauge. Also available in brown with UV-blocking effect for light sensitive samples.Scope of supply: Vacuum gauge, O-ring, drying agent tray, 2 x perforated sample trays (VDC-11 and VDC-21) or 3 x perforated sample trays (VDC-31 and VDC-41)
LLG-Vacuum desiccators, polycarbonate, round form, "Heavy Duty"
Cost effective alternative to glass desiccators. Highly transparent, lightweight, shatterproof, made of polycarbonate.Silicon O-ring and specially designed 'locking clip' allows use without grease and ensures an airtight seal. Flange lock holds the bottom and the lid together during non-vacuum conditions. Three-way stopcock provides great convenience for consistent vacuum draw, vacuum release or gas exchange e.g. inert gas. Maximum vacuum of 1.3 mbar (1.3 x 10-4 MPa) for more than 72 hours. Wide base provides superior stability. Hose connection outer diam. 9.5 mm.Scope of supply: Drying agent tray, perforated sample tray, O-ring and flange locker
LLG-Vacuum desiccators, polycarbonate, round form, "Heavy Duty", with vacuum gauge
Cost effective alternative to glass desiccators. Highly transparent, lightweight, shatterproof, made of polycarbonate.Silicon O-ring and specially designed 'locking clip' allows use without grease and ensures an airtight seal. Flange lock holds the bottom and the lid together during non-vacuum conditions. Three-way stopcock provides great convenience for consistent vacuum draw, vacuum release or gas exchange e.g. inert gas. Maximum vacuum of 1.3 mbar (1.3 x 10-4 MPa) for more than 72 hours. Wide base provides superior stability. Hose connection outer diam. 9.5 mm.Also available in brown with UV-blocking effect for light sensitive samples.Scope of supply: Drying agent tray, perforated sample tray, O-ring and flange locker
LLG-Vacuum measuring instrument DVR 2 pro
Versatile vacuum gauge for vacuum measurement between atmospheric pressure and 1 mbar.With integral, alumina ceramic, pressure transducer providing excellent corrosion resistance and long-term stability.Measurement principle: Capacitive; gas type-independent absolute pressure measurementMains independent due to battery operationLarge displayHigh measuring accuracyOptimal menu navigationWith support rodAll parts in contact with media are made of chemically resistant materialsDKD initial delivery calibration (Cat. No. 7.059 540) please order separately.Scope of supply: Vacuum measuring instrument with connections for small flange D16, compression fitting and tubing nozzle for tubing with 6 to 10 mm ID.
