Laboratory presses MP250
The laboratory presses are available as analogue models with pressure gauge or as digital models with digital pressure display. MP150 is ideal for IR spectroscopy, for 13 mm diameter press dies. MP250 is used in RFA analysis to form tablets with a diameter of 32 mm or 40 mm. For smaller press dies or more accurate pressure control, the MP150D or MP250D digital models are suitable.The MP150D and the MP250D can be equipped with a serial interface (optional). In addition, an individually programmable pressure limitation (optional) is available for setting the desired maximum pressure. Further pumping then does not build up higher pressure beyond the set value. This is especially useful if the sample should always be pressed with the same pressure. This makes every pressing process easy to control and reproduceable.Manual valve for controlled pressure reductionKeeps pressure stable for several hoursIntegrated splinter protectionIntegrated pressure control valvePress dies available from 3 to 50 mmWith connection for Vacuum pumpPlease order press dies separately.With pressure gauge (MP250) or digital pressure display (MP250D). Press for up to 25 tons pressure. Recommended for press dies up to 50 mm.SpecificationsPressure gauge Ø: Pressure:100 mm 25 tResolution:0.5 t / 0.01 tWidth between pistons:150 mmClear width min. / max.:73 mm / 185 mmSpindle diam.:45 mmSpindle path:112 mmPiston diameter / Stroke:107 mm / 22 mmDimensions (H min. / max. x W x D):497 / 609 x 370 x 300 mmWeight:approx. 51 kgPower supply MP250D:ext. power adapter, 12 V
Liquid sampler MiniSampler, PE
Taking samples is quick, easy, clean and practical.With the MiniSampler, the sample liquid only comes into contact with the suction hose and the sample bottle. Cross contamination is largely prevented. Bottles can be tightly sealed immediately after the sample is taken with a tamper-evident cap.The single use, PE suction hose can be quickly replaced, ensuring that samples are never contaminated. A new hose can be used for each sample if required. Because of its small diameter (8mm) and flexibility the hose can reach sampling areas that are otherwise inaccessible. Also suitable for viscous oils.Scope of supply: 10 x 100 ml PE bottles, 10 m of PE suction hose (6 x 8mm), 1 hose cutter , 1 hose weight (V2A/nickel-plated brass), 20 seal-it safety seal labels, carrying case
Liquid sampler UniSampler with flexible sample tubing
UniSampler with PVC hose and hose weight made of stainless steel. For deep, hard-to-reach places. The mass of the metal tube drags the hose to any depth.PVC sample tubing, 2.5 m longIncl. 1000ml sample bottle, manual vacuum pump and adapter for sample bottle, V2A hose weight, 20 seal-it safety seal labels, supplied complete in carrying caseUniversal bottle adapter made of PVC, for bottle necks Ø 24 mm, 31 mm, 39 mm and 50 mm nominal dimension
Liquid-Sampler, single hand operation, stainless steel V4A (1.4404), open with thumb
Sampler for thin to viscous liquids. Easy use with one-handed operation. With discharge funnel for safe filling of sample bottles.
Liquid-Sampler, single hand operation, stainless steel V4A (1.4404), place onto bottle
Sampler for thin to viscous liquids. Easy use with one-handed operation. With discharge funnel for safe filling of sample bottles.
LLG-Mortars, porcelain
According to DIN 12906. Suitable for easy grinding, comminution or crushing of ground material during sample preparation. With practical spout.Please order pestle separately.
LLG-Pestle, porcelain
According to DIN 12906. With rough or glazed friction surface for easy crushing of ground material during sample preparation.
LLG-Sample containers, PP, Heavy Duty, with screw cap, HDPE
Ideal for liquid specimen collection, transportation and storage.Ideally suited for liquid histological samplesContainer made of non-cytotoxic polypropyleneVery solid qualityTop and bottom gripping assures easy opening and closing when wearing glovesHalf-transparency containersWith graduationWith labelLeak proofFor research and development only.
LLG-Transport tubes, PP, with screw cap
For convenient storage and dispatch of samples.Conical bottomFree standingPrinted graduation1 1/4 turn thread design for super fast screwing
Manually-operated reels and lowering cables
Manually-operated reelsHigh winding capacity of up 150 m for cable 2 mm dia.Reel width: inner 44 mm, outer 55 mm, reel diameter: inner 100 mm, outer 180 mmPlease order the required lowering cable separatelyLowering cablesFor dipping bottles and immersion cylinders, matching manually-operated drum reels made of various materialsTensile load max. up to 10 kg
Measuring scoops, HDPE
Natural colouring. Conical in shape with tapered filling edge. Food-safe product according to regulation (EU) No. 10/2011.
Measuring scoops, PP
Measuring scoops which are also suitable as weighing scoops. With precision formed filling edge and comfortable, stable handle. Easily readable volume quantities on the upper side of the handle. Food-safe product according to regulation (EU) No. 10/2011.
Measuring scoops, PP, coloured
Also suitable as weighing scoops. Easily readable volume quantities on the upper side of the handle.Food-safe product according to regulation (EU) No. 10/2011.
Measuring scoops, PP, set, colour sorted
Also suitable as weighing scoops. Easily readable volume quantities on the upper side of the handle. Food-safe product according to regulation (EU) No. 10/2011.
Mesh, Polyamide
Thermo-fixed Polyamide (Nylon) mesh is temperature stable from -40 °C to 115 °C. In water from 95 °C to 100 °C. Stability in acids is limited and dependent on concentration and temperature. Nylon exhibits outstanding stability in alkalis, including sodium and potassium solutions. Its chemical behaviour with respect to organic solvents is moderate to good. Minimum mesh width: 102 cm, Length: 1 mOther sizes available on request.
Mesh, polyester
Thermo-fixed PE mesh with temperature resistance from -75 °C to 150 °C (short). For long term heating max. 125 °C. Resistant to acids but not alkalis.Dimensions: Minimum width 102 cm, Length 100 cm.Other sizes available on request.
Micro Ball Mill GT300
For grinding and mixing of hard, medium-hard, soft, elastic and fibrous samples. Also suitable for cell disruption and DNA/RNA extraction. The mill is designed for very short processing times and high sample throughput. The grinding containers carry out horizontal, circular-arc-shaped oscillations and the grinding balls ensure effective grinding and mixing of the sample.Only 30 seconds average processing time2 grinding stations for bowls with a volume of 5 to 50 mlMultifunctional clamping device, which also holds adapters for reaction vesselsGrinding time digitally adjustable from 1 second to 100 minutesVariable speed from 180 to 1800 min-1Control via LCD displayProgrammable grinding parameters, up to 10 programs can be storedTransparent coverSafety interlockGrinding chamber, clamping system and swivel arm made of stainless steelMaintenance-free direct driveGrinding bowls made of different materials with volumes up to 50 ml available as accessoriesGrinding bowls and balls are not included in the scope of supply and must be ordered separately.
Micro-Sampler, stainless steel
Without tip. V4A stainless steel. Sterilizable. GMP/FDA compliant. Specially for collecting small amounts of powder. Volumes of 0.2, 0.5, 1, 2, 5 and 10 ml can be taken simply, quickly and cleanly from different depths of sacks or containers. The Micro-Sampler tips are interchangeable so that tips with different volumes can be used.
Microfine grinder drive MF 10 basic
Universal laboratory grinder, comprising powerful drive unit for use with a choice of accessory grinding heads. The user can choose between the impact grinding head for milling hard, brittle materials (see fig.) and the cutting head for processing fibrous material. The maximum granule size output can be set by using various insert sieves (with apertures between 0.25 mm and 4 mm) placed above the outlet. There is an NS29 standard ground joint at the outlet for attachment of receiving flasks.Grinding/cutting heads not included.
Microtube holder for cup booster BR 30
For simultaneous sonification of pathogenic and toxic materials with: 1 perforated disc for 3 x 1.0 ml or 2.0 ml microtube cups each, 1 perforated disc for 3 x 0.5 ml microtube cups each, 1 perforated disc for 8 x 0.2 ml RPCR cups each.Converter and stand are not included.
Microtube holder for ultrasonic processing vessels BB 6, stainless steel
The microtube holder can hold up to 6 reaction cups (1.5/2 ml).
Milling chamber for Universal mill MultiDrive basic/control
Milling chamber with stainless steel beater for dry grinding of a variety of samples. The special vessel seal allows the pressure to be released via the lid during the grinding process of very fine powders.
Milling chamber with temperature sensor for Universal mill MultiDrive control
Milling chamber with stainless steel beater for dry grinding of a variety of samples. The special vessel seal allows the pressure to be released via the lid during the grinding process of very fine powders. A temperature limit (-50 to 120 °C) can be set and monitored using the integrated temperature sensor. Particularly suitable for temperature-sensitive materials.