Accessories NANOCOLOR®
*additional cable required**additional mains adapter required
Accessories NANOCOLOR®, Membrane Filtration
Turbidity elimination before photometric analysis (without digestion). Sample preparation set: 2 syringes 20 ml, 25 CHROMAFIL® membrane filtersMembrane filters CHROMAFIL® without accessories* with glass fiber pre-filter, retention of coarse particles without clogging.
Accessory holders for sedimentation cones with stopcock, PVC
Imhoff pattern, solid grey PVC. Stable design.
Accessory holders for sedimentation cones, PVC
Imhoff pattern, solid grey PVC. Stable design.
Adapter AD/SK for BOD measuring system OxiTop®
For OxiTop® measuring heads, for all sample and measuring bottles series PF45/.. and MF45/.., autoclavable (121 °C). Incl. OxiTop® AD adapter, OxiTop® SK screwable adapter, DI45 gasket for adapter VS45.
Ammonium reagents (NH4-N) for analyzer Alyza IQ NH4
For wet chemical reactions.
Automatic acidity burettes Dornic
Burettes for determining the acidity of a milk sample. Direct division in °D referred to 10 ml milk. With 500 ml polyethylene bottle and base.Automatic 0-point settingWith schellbach strips
behr COD Heating Blocks
COD acc. to ISO Precision heating blocks with 6, 12 or 24 sample positions. Flat surface heater for even temperature distribution to each sample position. Stainless steel and powder coated steel casing. Extensive insulation provides for inoffensive temperatures of the casing surfaces.End-to-end grooves in the precision aluminum plate at the bottom of the bores simplify sample handling and provide for exemplary safety of the analyst:During sample insertion the grooves cause pressure compensation. Thus even the most accurately fitting reaction vessels slip easily into the bores, which is required to effortlessly handle the behr insert and yoke type frames for RG 2 reaction vessels.When inserting the samples into the hot heating block adherent moisture on the vessel surface evaporates in sudden bursts. The grooves drain off the vapor which otherwise might cause the vessels to jump up and down which might eventually lead to the destruction of the vessels.In case of one or more vessels overflowing the liquid COD samples discharge through the grooves minimizing the danger of damages inside the block caused by acids.
behrosog 3 Scrubber
Infinitely variable throughputTransparent protective shield for safe operation of the unitExterior manual control elements with easy access prevent the analyst from touching hot glass partsAcid resistant diaphragm pump
behrotest ® HTI 1 manual titration station
The HTI 1 manual titration station consists ofa burette with digital display anda magnetic stirrer with a precisely fitting holder for COD reaction vessels. A screen serves as a neutral background and allows the user to determine the colour change at the end of the titration precisely. Therefore a titration could always carried out under similar visual conditions. This improves the precision and the reproducibility of the results.The precise positioning of the reaction vessels in the holder on the top of the magnetic stirrer also contributes to this. The angled wing of the screen protects against lateral dazzling light.SpecificationsVoltage230 VAC/ 115 VACFrequency50/60 HzWeightapprox. 3.5 kgDimensions in mm (W x D x H)approx. 330 x 200 x 600
behrotest® CF 2+2 and CF 6, Semi-automatic Crude Fibre Extraction
They are ideally suited for:total crude fibre determination (part of the Weender animal feed analysis as performed in Europe)neutral detergent fibre and acid detergent fibre determination (NDF and ADF according to Van Soest)acid detergent lignin determination (ADL according to Van Soest)different fractions of fibre (cellulose, hemicellulose and pectin) behrotest® semi-automatic crude fibre extraction units simplify everday life in the lab:Easy operationThe analyst is guided through the procedure by messages on the display.behr ABP ("acknowledge before proceeding") method for optimum analytical safety. Possible manual operation of air and suction pumps.
behrotest® Multi-sample Extractors for Twisselmann Extraction
Economical and user-friendly units for extraction in accordance with Twisselmann:each sample position is individually adjustablecooling water distributor ensures an even cooling at all sample positionspractical stand for holding the condensers securely between the extractionsmounts for holding the spacers after the removal of the sample containers
BOD measurement system OxiTop®-i IS 6 / 12
Easy-to-use, respirometric measuring system for determining the biological oxygen demand (BOD). The method is based on changes of pressure in a closed system using measuring heads attached to the sample bottles. The BOD can be determined simultaneously in up to 6 or 12 samples.No dilution of the sample requiredDirect reading of the BOD, the time course and the intermediate values on the graphical display of the measuring headsInput of the used sample volume directly at the measuring headMonitoring time between 1 and 7 daysPermanent display of the current status at each measuring headColoured measuring heads with adjustable, numerical sample identificationScope of supply: OxiTop®-i IS 6: 6 x measuring heads (3 x blue, 3 x grey), 6 x sample bottles PF600, 6 x rubber quivers, overflow measurement flasks, 6 x stirring rods, stirring rod remover, stirring platform SI 6OxiTop®-i IS 12: 12 x measuring heads (6 x blue, 6 x grey), 12 x sample bottles PF600, 12 x rubber quivers, overflow measurement flasks, 12 x stirring rods, stirring rod remover, stirring platform SI 12An incubator is required to operate the OxiTop®-i IS. Please order separately.
BOD Measuring system OxiTop®-IDS B6 for determination of soil respiration
Respirometric measuring system for 6 measuring heads for determination of aerobic soil respiration, OxiTop®-IDS B6M-2.5 acc. to AT4 guideline. These sets are suitable for forecast, survey and monitoring of clean-up operations as well as measurement of bio-degradation of pesticides, fungicides, insecticides and fertilizers for example.With the proven Bluetooth® connectivity and the convenient operation via MultiLine® multi parameter instrument Multi 3620 IDS or Multi 3630 IDS. Using a Multi 3620 IDS or Multi 3630 IDS in BOD special mode the BOD measuring range extends to 400000 mg/l. For an already existing Multi 3620 or 3630 IDS, a firmware update is sufficient. Herewith beneath the OxiTop® applications also measurement of pH, conductivity, solved oxygen and turbidity are available. All heads can be used independently for routine BOD measurements from 1 to 7 days.Bluetooth® connectivityDirect calculation of all results in the meterRepresentation of curves for monitoringParallel measurement of different examinations and methodsExport to data acquisition programsMeasurement duration selectable (0.5 hours to 180 days)Please order CO2 absorber NHP 600 (9.303 403) separately.The IDS multi parameter measuring instruments Multi 3620 IDS Set WL or Multi 3630 IDS Set WL are required. Please order separately.Scope of supply: 6 measuring heads, 6 sample bottles PF45/500 (500 ml), 6 adapters OxiTop® AD/SK