Thermometers TFN, with SMP connection
Thermometers for use with thermocouples (Type K, J, T, E).Applications:Heating / Air-conditioning, ventilation / Air, gases, fluids / Surface temperature / Plastic materials / LaboratoriesAttributes:Robust and impact resistantMin/Max, Hold facility°C/°F selectableBattery charge status indicatorChangeable batteryFactory calibration certificateThermometers for use with thermocouples (Type K, J, T, E).Applications:Heating / Air-conditioning, ventilation / Air, gases, fluids / Surface temperature / Plastic materials / LaboratoriesAttributes:Robust and impact resistantMin/Max, Hold facility°C/°F selectableBattery charge status indicatorChangeable batteryFactory calibration certificate
Thermometers, digital, P300
Splash-proof, robust and handy.Ideal for measurements under tough environmental conditions.Illuminated display with large digitsMemory for Max. and Min. valuesHold functionIntegral probe holder enables one-handed operationLong battery life (uses 2 x 1.5 V AA batteries)Compact size: 130 x 65 x 25 mmModel P300 is supplied with fixed penetration probe, 120 x 4 mm L x Ø 4mm, model P310 is without probe.For P310: storage case, plastic with foam insert.
Thermometers, ground glass joint
Precision thermometers with cone NS 14/23, top end melted round, frosted glass scale with black scale
Thermometers, standard ground joint
With NS 14.5/23 cone. Enclosed-scale type, Translucent glass scale. Upper section approx. 11 mm diameter, lower section 7.5 mm diameter. Richter-top finish seal without button. Suitable for official calibration.
Thermoprobe Bola - Lemo Type Pt100
Ideal for measuring temperature in agressive media. The probe is housed in a stainless steel tube and therefore still has the necessary flexiblity. It can be gently manoeuvred into the right direction. The additional PTFE-coating gives the important chemical resistance. For a direct and quick measurement the PTFE-coating is reduced at the measuring tip (5.5 mm diameter). The connector is a size 1 Lemo-type, with 4-lead cable. The cable has a total length of 1500 mm and is also well coated with PTFE. Temperature resistance maximum +300°C and minimum -70°C, without charge.
Thermostat vessel for ViscoClock plus, DURAN®
For tempering of samples in a viscometer, as an alternative to a special glass-panelled bath thermostat. ViscoClock plus has to be connected via hoses to a suitable thermostat bath circulator. For safety reasons, the range of measuring temperatures is restricted to ±15 °C compared to room temperature. The use of an additional magnetic stirrer is recommended.Temperature range: 10 to 40 °CAccuracy: ±0.05 KTubing olive (diam.): 10.5 mmMagnetic stirring bar: approx. 40 mm
Time/Temperature indicators MonitorMark™
MonitorMark™ Time Temperature Indicator solves the challenge of monitoring thermal exposure of temperature-sensitive products during transportation and storage. The large indicator window displays exposure, the smaller windows to the right indicate for how long temperature exposure took place.Clear display of temperature exceedances and the duration of the exceedanceSelf-adhesive, easy to apply
Tomb stone tester FL-G
Electronic tombstone tester for testing the stability of tombstones in accordance with VSG 4.7.Turnable display with backlightPeak Hold ModeMetal housingStainless steel handle with rubber coveringWide pressure plate with foam rubber surface, so that the tombstone does not get scratched when force is appliedFunction to set limits with visual signalInternal memory for up to 500 measurementsData interface USB, RS-232Rechargeable batteryScope of supply:Force gauge FL, handle, pressure plate, mains adapter
Ultra-micro- and micro balances Cubis® II
Modular premium balances for research and development or analytical laboratories. The Cubis® II platform is a completely configurable, high-performance portfolio of both lab weighing hardware and software. The combinability of the display unit, weighing module, draft shield and software packages for various applications and functions allows the individual adaptation to all weighing tasks.Monolithical weighing systemSeamless connectivity to diverse laboratory information systems without the need of additional softwareIntegrated climate sensorStatus center notificationsFull data integrity following ALCOA+ principlesSupports all requirements for FDA directive 21 CFR part 11 and EU Annex 11 complianceComplete traceability via advanced audit trail and reporting functionMCE Essential User Interface:Large, high-contrast TFT touch displayFactory-installed basic set of essential weighing applicationsActivated by touch key, touch-free using IR sensor or gesture sensor (optional)MCA Advanced User Interface:Large 7" color touch displayFactory-installed basic set of essential weighing applicationsVarious QApp packages for optional software extensionActivated by touch key, touch-free using IR sensor or gesture sensor (optional)Titanium inner partsAutomatic motorised levellingAutomatic, motorized, round, glass draft shield with learning capability, illumination and integrated motion sensorHeight and weight depending upon weighing pan size, filter weighing pan and draft shield. Verified balances and other configurations are available online or on request.
Ultra-micro- and micro balances Cubis® II
Modular premium balances for research and development or analytical laboratories. The Cubis® II platform is a completely configurable, high-performance portfolio of both lab weighing hardware and software. The combinability of the display unit, weighing module, draft shield and software packages for various applications and functions allows the individual adaptation to all weighing tasks.Monolithical weighing systemSeamless connectivity to diverse laboratory information systems without the need of additional softwareIntegrated climate sensorStatus center notificationsFull data integrity following ALCOA+ principlesSupports all requirements for FDA directive 21 CFR part 11 and EU Annex 11 complianceComplete traceability via advanced audit trail and reporting functionMCE Essential User Interface:Large, high-contrast TFT touch displayFactory-installed basic set of essential weighing applicationsActivated by touch key, touch-free using IR sensor or gesture sensor (optional)MCA Advanced User Interface:Large 7" color touch displayFactory-installed basic set of essential weighing applicationsVarious QApp packages for optional software extensionActivated by touch key, touch-free using IR sensor or gesture sensor (optional)Titanium inner partsAutomatic motorised levellingAutomatic, motorized, round, glass draft shield with learning capability, illumination and integrated motion sensorHeight and weight depending upon weighing pan size, filter weighing pan and draft shield. Verified balances and other configurations are available online or on request.Verified balance with EC Type Approval Certificate, for EU except France.
Ultra-micro- and micro balances Cubis® II, with filter draft shield
Modular premium balances for research and development or analytical laboratories. The Cubis® II platform is a completely configurable, high-performance portfolio of both lab weighing hardware and software. The combinability of the display unit, weighing module, draft shield and software packages for various applications and functions allows the individual adaptation to all weighing tasks.Monolithical weighing systemSeamless connectivity to diverse laboratory information systems without the need of additional softwareIntegrated climate sensorStatus center notificationsFull data integrity following ALCOA+ principlesSupports all requirements for FDA directive 21 CFR part 11 and EU Annex 11 complianceComplete traceability via advanced audit trail and reporting functionMCE Essential User Interface:Large, high-contrast TFT touch displayFactory-installed basic set of essential weighing applicationsActivated by touch key, touch-free using IR sensor or gesture sensor (optional)MCA Advanced User Interface:Large 7" color touch displayFactory-installed basic set of essential weighing applicationsVarious QApp packages for optional software extensionActivated by touch key, touch-free using IR sensor or gesture sensor (optional)Titanium inner partsAutomatic motorised levellingManual stainless steel draft shield for filter weighing applicationsHeight and weight depending upon weighing pan size, filter weighing pan and draft shield. Verified balances and other configurations are available online or on request.
Ultra-micro- and micro balances Cubis® II, with filter draft shield
Modular premium balances for research and development or analytical laboratories. The Cubis® II platform is a completely configurable, high-performance portfolio of both lab weighing hardware and software. The combinability of the display unit, weighing module, draft shield and software packages for various applications and functions allows the individual adaptation to all weighing tasks.Monolithical weighing systemSeamless connectivity to diverse laboratory information systems without the need of additional softwareIntegrated climate sensorStatus center notificationsFull data integrity following ALCOA+ principlesSupports all requirements for FDA directive 21 CFR part 11 and EU Annex 11 complianceComplete traceability via advanced audit trail and reporting functionMCE Essential User Interface:Large, high-contrast TFT touch displayFactory-installed basic set of essential weighing applicationsActivated by touch key, touch-free using IR sensor or gesture sensor (optional)MCA Advanced User Interface:Large 7" color touch displayFactory-installed basic set of essential weighing applicationsVarious QApp packages for optional software extensionActivated by touch key, touch-free using IR sensor or gesture sensor (optional)Titanium inner partsAutomatic motorised levellingManual stainless steel draft shield for filter weighing applicationsHeight and weight depending upon weighing pan size, filter weighing pan and draft shield. Verified balances and other configurations are available online or on request.Verified balance with EC Type Approval Certificate, for EU except France.
Ultrasonic flow meter UMI 880
Ultrasonic flow meter for measuring flow velocity and volume flow.Maintenance-free, as there are no moving partsWith data logger function (32 GB memory capacity)2.8" LCD displayUSB interfaceEasy assemblyInstallation without process interruptionNo pressure lossScope of supply: Ultrasonic flow meter, 2 x flow sensor UMI 880 S1 (for pipes with Ø 20 to 108 mm), 2 x connection cable 5 m, 2 x detachable cable tie, power supply unit, USB-C cable, ultrasonic coupling gel, measuring tape, plastic carrying case, operating manualSpecificationsMeasuring range:-32 ... 32 m/sResolution:0.001 m/sAccuracy:±1.5 % of measured value (for Ø 50 mm), ±3.5 % of measured value (for Ø 50 mm)
Ultrasonic flow meter UMI 880 Pro
Ultrasonic flow meter for measuring flow velocity and volume flow.Maintenance-free, as there are no moving partsWith data logger function (32 GB memory capacity)2.8" LCD displayUSB interfaceEasy assemblyInstallation without process interruptionNo pressure lossThe ultrasonic flow meter UMI 880 Pro can additionally measure heat output and heat quantity.Scope of supply: Ultrasonic flow meter, 2 x flow sensor UMI 880 S1 (for pipes with Ø 20 to 108 mm), 2 x temperature contact sensor, 2 x connection cable 5 m, 2 x detachable cable tie, power supply unit, USB-C cable, ultrasonic coupling gel, measuring tape, plastic carrying case, operating manualSpecificationsMeasuring range:-32 ... 32 m/sResolution:0.001 m/sAccuracy:±1.5 % of measured value (for Ø 50 mm), ±3.5 % of measured value (for Ø 50 mm)
Ultrasonic thickness gauge TB-US
For measuring of cast iron, aluminium, copper, brass, zinc, quartz glass, polyehylene, PVC, grey cast iron, nodular cast iron, steel.Selectable measuring units: mm, inchAuto-Power-OffBattery operationScope of supply:Ultrasonic thickness gauge, external sensor (Ø 8 mm), base plate, carrying case
Ultrasonic thickness gauge TD-US
Selectable measuring units: mm, inchData interface RS-232Battery operationScope of supply:Ultrasonic thickness gauge, base plate for adjustment, external sensor (8 mm), carrying case
Ultrasonic thickness gauge TN-GOLD
For checking the authenticity of gold bars and coins. The SAUTER SSG software can be used to calculate the sound velocity for various precious metal alloys. This makes it possible to determine whether coins or ingots contain false cores or whether they consist of one and the same material.Selectable measuring units: mm, inchInternal memory for up to 20 files (with up to 100 values per file)Battery operationAUTO-OFF functionData interface USBScope of supply:Ultrasonic material thickness gauge, base plate for adjustment, carrying case
Ultrasonic thickness gauge TN-US
Scan mode (10 measurements per sec.) or single point measuring modeInternal memory for up to 20 files (with up to 100 values per file)Selectable measuring units: mm, inchBattery operationUSB data interfaces as standard (for models with readout 0.01 mm)Scope of supply:Ultrasonic thickness gauge, external sensor, carrying case
Undergloves, Cotton
100% Cotton. Monofilament, ideal to wear under chemical protection gloves. 1 pair per pack. Cat. I
Universal digital thermometers, Multi
Measuring range -50 to 200 °C x 0.1 °C, switchable to °F. Hfunction and 125 x 3.5mm stainless steel penetration probe. With battery.Maxi-T and Maxi-Pen with maximum-minimum memory and water-proof casing.
Universal indicator paper Tritest L
For determination of pH value.Roll length 5 m, 14 mm width. With 3 colour zones and 2 hydrophobic zones. The zones are separated by a hydrophobic barrier, which effectively prevents mixing of the reaction colours and increases mechanical stability.Plastic container with 1 roll of indicator paper and colour scale.
Universal indicator papers
For determination of pH- value.Plastic dispensing reel with 1 roll of indicator paper and colour scale.Further indicatorpapers available on request.
Upgrade set test stand TVL-XL
With the extension kit for SAUTER TVL, the work zone is extended by 250 mm, which means that even larger test items can be measured. The travel path (spindle height from the base plate) remains the same when doing this: 230 mm. Casing material: metal, lacquered.
USB charger for wireless module IDS WLM-S
Cascadable USB charging station without power supply unit for the IDS WLM-S sensor modules. For charging with or without connected electrode.Please order power supply unit separately.